Tuesday, March 31, 2009

Inaugural Brew - 3665 IPA

There's nothing like trying to use your brain after a wedding reception and a late night after party, but c'est la vie...we still got to brewing on Sunday as planned. We had an unexpected overnight guest, but he came in handy when I whimsically mentioned that it would be nice if I had some copper tubing to make a chiller. Lee is in the plumbing business, so it's not that unusual for him to have 50 ft. of 3/8" copper tubing laying around. He went home to grab some clothes and copper, and Keith arrived just before he got back. I guess Lee ran into his brother at his house, because the infamous Chef Brandon showed up to see what was going on. Last, but not least, my dad stopped by to drop my kids off and couldn't resist getting into some engineering of a heat exchanger (immersion chiller). So, we used what we had (the frying cage of a turkey fryer) and made a nice homemade chiller.









After a beer break and some time with the kids and a football, we got started with the brew.

Here's the recipe:



3665 IPA

OG: 1.068
IBU: 44.7

5 lbs. Light - Dry Extract
2.0 lbs. Pale Malt - Grain
1.75 lbs. Vienna Malt - Grain
1.0 lb. Caramel/Crystal Malt (20L) - Grain
0.5 oz Cascade hop pellets @ 60 min.
0.5 oz Cascade hop pellets @ 20 min.
0.5 oz Cascade hop pellets @ 15 min.
0.5 oz Cascade hop pellets @ 10 min.
1.0 oz Cascade hop pellets @ 5 min.
1.0 oz Cascade hop pellets - dry hop
1/4 tsp. Irish Moss @ 10 min.
1 pkg. Wyeast 1052 American Ale


So, we started with the grain to get that going....that was a fiasco. The sock that we poured it into wasn't cooperating so we lost a little. I wish I could say that was the worst of our mistakes, but more to come. We did a fairly decent job at steeping the grains at 160-165 deg., but it was somewhat difficult to maintain without kicking on the burner every 5-10 min. After steeping for 45 min., we took the grain bag, put it into a fryer basket, and poured 1 gallon of 165 deg. water to rinse the remaining sugars out before discarding.

Once that was finished, we pulled an Emeril and kicked it up a notch. The wort got to a boil faster than I expected, and we had a slight boil over when I ran inside to get another beer. We didn't lose too much, but it did add up to mistake #2. Lee and I then added the extract and 1st round of hops; that's when everything started smelling good. I also think it caused more drinking, which in turn, caused a beer run. "Remember, NO TWIST OFFS!"...they got the message.


Everything was going according to plan until the last few minutes when the thought ran through my head, "Shite! Irish moss!" I mean really, who's going to drink a beer that didn't coagulate the proteins? I got it in there with 3 minutes before the boil was over, so I hope it helped at least a little.







Keith and I then carted the kettle over to our chilling station (aka the corner of the yard where rain water runs off). Our homemade chiller needs some refinement, especially the brass fittings. It leaked a bit so we had to make sure to have the connections low enough not to spray into our nice sterile wort. After getting it running and watching Keith get a 1st degree burn while saying, I wonder how hot this water gets on this end....AHHHH!!! @$#@!...we went to get another beer and sanitize the bucket while it was cooling. We come back to check it out, and there is a freaking honey bee sucking on our wort! I don't know if he actually got into the brew, but when we lifted the lid, he was chowing on the inside of the kettle...mistake #3...don't go get beer while your beer is exposed. The good news is that our chiller did a fine job chillin', and our wort was cooled in less than 15 minutes.

We then took 2-1/2 gallons of distilled water, shook it up in the jug to aerate, and poured it in. Then we poured in the wort and had a nice volume of 5 gallons. Mistake #4...forgot to sanitize the hydrometer...next time will keep the extra bucket full of sanitizer for this reason. You would think after all of the information that I digested, I would have run across a how-to for using a hydrometer...no dice...trial and error. I felt like an idiot after trying to hold it like a thermometer in the wort and then figured out that it was supposed to float...duh...measures the density of the water...hello!? We got a reading of 1.068, which was only 7 pts. shy of the 1.075 that I expected from the recipe...I'll blame the boil over. :)

After we finished that up, we sealed her up and put her away in the utility closet. After racking my brain trying to make sure that we had done everything right, I remembered a small detail....the damn yeast. Yep, that's right. If I wouldn't have been so anal to go through the list in my head, we could have had some aged wort. Fortunately, we had already smacked it 4 hours before and it was sanitized and ready to go.


I won't go into too much detail, but that didn't end the day. We continued with the beer fest by sampling some other tasty brews in preparation for our next brew day.

We then had Brandon whip up some nice Steelhead Trout, Homemade Mac & Parm Cheese (freakin awesome), with blanched asparagus sauteed with shallots...not too bad for a bunch of beer drinkers.

2 comments:

  1. OMG I enjoyed your blog very much!!! Especially since you included pics. Ironically (and let me first say I know NOTHING) about brewing beer...) Matt is quite the enthusiast of home brewing. He's more into the Belgian ales, and has made some really nice beers with the set-up that he has. He can attest that it takes a bit of a scientific approach and a lot of attention to detail (oh, and I think he does it sober, LOL!!!) But kudos to you and your pals for gettin' it done.

    ReplyDelete
  2. Sounds like you will cut out 3/4ths of your mistakes if you just keep a cooler of beer handy at all time. :)

    Hope I can be around for the next brewing, I could stand to learn a few things about the making end of things. I've got the drinking part down, for sure.

    ReplyDelete